Skip to main content
Free shipping
Shipping within 24h
30 days money back guarantee
Purchase comfortable on account
Hotline +49(0)7223-800130-0

Defender axle correction set for lifting

Product information "Defender axle correction set for lifting"

Caster correction front axle for Land Rover Defender.

Land Rover Defender axle caster correction kit for the front axle made of high performance polyurethane for vehicles with discreet lift. In case of chassis modifications respectively a slight lifting the axle geometry has to be adjusted as well. If you modify your vehicle, you should do it properly.

This heavy-duty correction kit can be used for lift from about 25 to 40 mm. However, we recommend such an adjustment only for vehicles that are not exposed to adverse conditions.

Information

  • Bushings tie rods front axle correspond (NTC6781)
  • Bushings mounting tie rods front axle frame side (ANR6971 NRC4514)
  • Material Polyurethane
  • From chassis number LA930456 > until year of manufacture 01.2016

Zubehör

Only 5 available
ENGAGE4X4 High Performance Shock Absorber Set Step 1
ENGAGE4X4 high performance shock absorbers Step1 for the Land Rover Defender have been developed for the highest loads and extreme requirements. The high performance shock absorbers are designed 80% stronger than conventional monotube or twin-tube shock absorbers. High-performance shock absorbers ENGAGE4X4 Step 1 for all Defender All components are CNC machined from high quality materials. ENGAGE4X4 high performance shock absorbers are fully revisable and can also be tuned to suit different spring rates or various requirements. The rear shocks are equipped with a special bronze dust cap, which makes it impossible for dust and mud to damage the oil seal of the shock absorber. Fields of application Off road, trail, trophy, working, protected vehicles, expeditions, Specifications:Type: monotubePiston: 46 mmPiston rod: 22 mmOil: High performance oil OR-SpecialGAS: Nitrogen 5.0Pressure: Standard 9 BarFillable: min.: 5 - max. 22 Bar depending on settingMaterial:Eye: Fortal 7075Piston: ETG100Piston rod: 20MnCR4 high polishedBody: Precision milled steel tube. Fits:Defender; Discovery 1, Range Rover classic.

€2,490.00*
Heavy duty shock absorber Land Rover Defender 110 & 130 rear axle
Heavy Duty Shock Absorber for Defender 110 / 130 Rear Axle Defender 110 and 130 heavy duty shock absorbers suitable for rear axle in (reproduction) spare parts quality. The technical characteristics heavy duty shock absorbers for Land Rover Defender 110 and 130 TDI refer to the application of higher loads in everyday use, they are exactly matched to the vehicle specifications of the original Defender chassis and thus give more security when driving in trailer operation and for the use of vehicles with higher payloads. Information Installed quantity/vehicle 2 pieces (always renew in pairs) Parts quality: AFTERMADE From chassis number to WA159806 (all Land Rover Defender from Turbo Diesel to TDI 300)

€73.80*
Only 3 available
ENGAGE4X4 progressive suspension springs for Defender 90
ENGAGE4X4 high performance suspension springs including TÜV parts certificate. ENGAGE4X4 suspension springs for the Land Rover Defender 90 are progressively wound with coil-off at the front axle. This allows 40-50mm longer shock absorbers to be installed and significantly increases axle articulation. Due to the extreme progressive winding of the front axle, a very sensitive response is achieved in conjunction with monotube gas shock absorbers. Information Areas of application: On Road, Off Road, Rally Raid Spring winding: Progressive with winding cutoff on the VA. Lifting: Defender 90 +40 to 50 mm Approved: TÜV parts certificate Coating: EPS powder coating

Content: 4 Paket(e) (€214.75* / 1 Paket(e))

€859.00*
Only 2 available
Bearing bush tie rods (frame side)
Bearing tie rods for all Land Rover Defender & Discovery 1. Tie rod rubber bearing on frame for all Defender and Discovery 1 models up to chassis number VA130784 in OEM parts quality. Information Up to chassis number: VA130784 Installed quantity/vehicle 4 pieces (quantity to be ordered 1 set = 4 pieces)

€13.90*
Only 5 available
New
Tie rods for Land Rover Defender with caster correction including TÜV parts certificate
Often it is not done with four suspension springs and four shock absorbers. With Land Rover Defender suspension lift, the entire suspension geometry of your Land Rover Defender changes. All suspension lifts on a Land Rover Defender over 25 mm need a correction, all related components. Especially for the Land Rover TD4 models from the model years 2007 onwards, it is particularly important to carry out a correct suspension installation. Very quickly unpleasant vibrations occur in the drivetrain, which lead to consequential damage. Land Rover Defender tie rods with 3° caster correction and TÜV A good suspension for your Defender consists of: Tie rods with caster adjustment (front axle), push rods(rear axle), an adjustable Panhard rod, double cardan shafts and if necessary extended brake hoses. Possibly with adjustable shock absorbers reinforced damper domes (open) on the front axle. All parts should be supplied with a TÜV parts certificate, otherwise there may be liability problems in the event of an accident. The trailing arms of the Defender with caster correction are absolutely necessary for suspension lift over 25mm. We recommend to use only original or Superpro suspension bushings. (suspension bushings are not included in the price) Information Material: QSTE 500TM Tested: TÜV Austria Document: Parts certificate Caster manufacture Heat treated Shot peened Zinc primed Powder coated Optimized for better steering angle with larger tires

€1,159.00*
Only 3 available
Panhard rod adjustable for Land Rover Defender with TÜV parts certificate
ENGAGE4X4 Panhard bar adjustable for the Land Rover Defender and Discovery with TÜV parts certificate. With 4 springs and 4 shock absorbers a suspension upgrade on the Land Rover Defender is far from done. Most suppliers sell suspension springs and shock absorbers with TÜV.However, what about suspension geometry? When the vehicle height on the Defender is changed due to a set of springs, the front axle shifts to the left. The wheels of the rear axle run quasi offset to the rear axle. As a result, the load on the suspension bushings and other suspension parts changes and may wear out sooner. At the same time, the vehicle pulls to the right when braking. Advantages of the adjustable ENGAGE4X4 Panhard bar TÜV parts certificate > for easy registration Fine thread > for exact adjustment EPS powder coating and blue galvanized thread > for best corrosion protection Made in Germany > for consistent quality Information Material: High performance steel tube S355 Thread: Fine thread Coating: EPS powder coating Thread coating: Blue zinc plated Please note the bushings are not included. For use in Discovery 1 and Range Rover Classic mounting points must be adjusted to M16 or Matching bushings with M14 bolt diameter.

€819.00*
Only 8 available
Defender 110 suspension springs + 15 to 30 mm from ENGAGE4X4
ENGAGE4X4 high performance suspension springs including TÜV parts certificate. ENGAGE4X4 suspension springs for the Land Rover Defender are progressively wound with coil-off at the front axle. This allows 40-50mm longer shock absorbers to be installed and significantly increases axle articulation. Due to the extreme progressive winding of the front axle, a very sensitive response is achieved in conjunction with monotube gas shock absorbers. Information Areas of application: On Road, Off Road, Rally Raid Spring winding: Progressive with coil cut-off at the VA Raising: Defender 110 approx +25mm Defender Approved: TÜV parts certificate Coating: EPS powder coating

€859.00*
Land Rover Defender front axle tie rod suspension bushing
Suspension Bushings Tie Rod Axle Bearing Land Rover Defender suspension bushings set for the tie rods Information Installed quantity/vehicles 4 pieces Delivery quantity 4 pieces Suitable for vehicles from chassis number LA930456

€25.20*
Only 2 available
Shock absorber Defender 90 rear axle
Shock Absorber for Land Rover Defender 90 Rear Axle Defender 90 shock absorber from Boge for the rear axle OEM parts quality. Comes complete with mounting hardware. The technical characteristics are precisely matched to the vehicle specifications and contribute to a noticeable improvement in the handling of the Defender. High quality components and sophisticated manufacturing processes guarantee the best quality and comfort for your vehicle. Information Installed quantity/vehicle 2 pieces (always renew in pairs) From chassis number XA159807 to ENDE Manufacturer Boge (OEM)

€72.85*

Alternative Produkte

Only 2 available
Suspension bushing set polyurethane
Polyurethane is a petroleum-based synthetic plastic available in many grades. Low-quality materials are often used in industrial applications. However, there are also extremely high-performance polyurethane materials. This is used in the high-performance bushings for the Land Rover Defender. It is a particularly temperature-resistant oil. It is also diesel resistant and enormously resilient to permanent deformation. The Land Rover Defender high performance suspension bushing kit is designed to withstand particularly heavy off-road loads. Special vehicles that are regularly driven off-road and in the most adverse conditions require high quality heavy duty bushings to increase durability. These PU suspension bushings are made of a special polyurethane compound. The so-called hardness grade has been specially developed for extreme loads for the Defender. Land Rover Defender high performance suspension bushing set complete The field of application for the Defender is as versatile as its fans. With the high-performance suspension bushings, the improvement begins with the chassis handling to the improvement of durability under the toughest loads with overloaded vehicle in the most extreme off-road applications. Especially protected Land Rover Defenders in military use suffer from handling & durability problems under normal road driving due to the extremely high dead weight. The high performance bushings are ideal for long distance travel and vehicles with trailer operation. Steering becomes much more rigid and direct on the road. The tendency to roll is minimized. Road safety improves significantly and durability increases many times over for off-road applications. Information Installation time approx. 8 hours Areas of application, protected vehicles, long-distance vehicles, trailer operation, improvement of handling in road traffic. The set includes: 4x bushings tie rods (front-axle side) 4x silent bearing tie rods (frame side) 2x bushings push rods (rear-axle side) 2x silent bearing unit (frame side) 2x bushings Panhard rod 2x bushings wishbone (frame side) 4x assembly grease

€309.00*
Only 4 available
Tip
Bolt set suspension rear axle Land Rover Defender
Screw set rear axle Land Rover Defender from year of manufacture 2009Our pre-assembled bolt set for suspension bushings on the rear axle of the Land Rover Defender, manufactured for vehicles from year of manufacture 2009 to 2016, is the ideal solution for the Maintenance and replacement of the bushings. This high quality bolt set contains all the necessary bolts for precise and reliable installation. Each screw has been carefully selected, to ensure a perfect fit and long life. With this bolt set you can keep your suspension in top condition and enjoy an optimal driving experience. Invest in quality and order our Rear Axle Suspension Bushing Bolt Set today for optimum care and maintenance of your Land Rover Defender.

€39.90*
Bolt set Defender chassis
Bolt set Defender suspension front axle for all Land Rover Defender TD5 from VIN XA159807 - 2A620000

€55.90*
Only 2 available
Bolt set suspension Defender & Range Rover Classic front axle
Bolt set for suspension mounting Defender front axle. Includes bolts and nut for mounting the Panhard rod and tie rods. Information Defender - LA930456 to WA159806 Range Rover Classic - 1992 - 1994

€39.90*
Only 2 available
Bolt set Land Rover Defender front from VIN KA
Land Rover Defender suspension bolt set (front axle) for trailing arm (bushes NTC6781 and Panhard rod ANR3410) up to chassis no. KA930455 Information Installed quantity 1 Original equipment manufacturer Chassis front axle Suitable for Defender up to chassis no. KA930455

€29.90*