Double cardan shaft Defender 110 TD5 rear axle (4-fold greasable)

Double-joint propshaft Land Rover Defender When the chassis is raised more than 25 mm, rotational vibrations occur in the driveline of the Defender TD4. These mostly occur in the, at a speed of slightly more than 80 km/h and can damage the transfer case in the long run. The ENGAGE4X4 double-joint propshaft prevents the vibrations in the driveline of the raised Defender through a stress-free working angle. In this way, height increases of around 100 mm are possible. Thus, the ENGAGE4X4 double-joint propshaft is absolutely necessary for Land Rover Defenders with a suspension lift, in order to carry out a durable suspension modification on the Defender. Another special feature is the new lubricatable sliding piece developed by ENGAGE4X4, here the grease nipple is protected, so that the shaft can be maintained even after extreme off-road use. Continuous improvement and long-term testing in our vehicles. In 2018, a journey was started from Germany to Mongolia and back around 20,000 km, including 3,500 km under the most adverse conditions in the steppe of Mongolia and many off-road passages in Russia and Kazakhstan. The ENGAGE4X4 double-jointed cardan shaft had been installed for more than 6 years at this point and had run 45,000 km with a suspension increase of 80 mm. Also on this tour no defect was found at the shaft. Our ENGAGE4X4 double-joint cardan shaft has gone through a steady improvement trip over 9 years. Countless improvements, tests with the manufacturer and durability tests as well as long-term tests over years have made this propshaft unique. Available for all Land Rover modelsFor the Land Rover Defender suitable for the front axle and the Defender 90 TDI & TD5 suitable for the rear axle. The ENGAGE4X4 propshafts are designed for very heavy duty off road use. The sliding piece of this Defender propshaft is protected with a Simmering against the penetration of dirty water. The reinforced universal joints can be lubricated. The shaft operates stress-free at large interlocks at angles up to 35°. Information Land Rover Defender TD4 (all models) on the front axle Land Rover Defender 90 TD5 & TDI on rear axle Cross sets: Reinforced 30mm (greasable) Length compensation: 110mm Sliding piece: Toothing plastic coated and sealed with Simmering (greasable) Flange: Fits flange (original Defender flange) Manufacturer Standard: ISO:9001 & TS:16949 ApplicationsOff Road, Trophy, Rally Raid, protected vehicles, higher mounted vehicles, expedition vehicles for long distance travel

ENGAGE4X4 Wide Angle Cardan Shaft Defender Cardan shafts from ENGAGE4X4 are made in Germany and are only manufactured with OE parts to ensure long durability. All cardan shafts have been tested, developed and continuously improved by us over many years. The universal joints are much stronger than the original standard joints. ENGAGE4 Wide Angle Cardan Shaft Defender for high durability in off-road conditions The ENGAGE4X4 cardan shafts are designed for very heavy loads in off-road operation. The sliding piece of this Defender propshaft is protected from the ingress of dirty water by a Simmering. The reinforced universal joints are equipped with special PU thrust washers (high performance seal) according to construction machinery standard. The universal joints can be lubricated centrally. The shaft operates stress-free at a large entanglement at an angle of up to 30°. ENGAGE4X4 wide angle cardan shafts are of great advantage on Defenders with a low chassis lift max. 20 mm and a higher axle articulation. Thus, the universal joints are not overstressed in the deflected state. The sliding piece with over 110 mm length compensation can be lubricated on all shafts since 2014. The grease nipple is protected from tearing off by a metal ring. So that the shaft can still be maintained even after extreme off-road use. Information Areas of application, off road, trophy, rally raid, protected vehicles, higher vehicles Cross sets reinforced 30 mm with PU thrust washers (greasable) Length compensation 110mm Sliding piece toothing plastic coated and sealed with Simmering (greasable) Fits original Defender flange Manufacturer Standard: ISO:9001 & TS:16949

Screw set for Land Rover cardan shaft front axle No tiresome searching of spare part numbers, simply order a preassembled assembly set. You want to replace the cardan shaft or universal joints. Just order a ready-made repair kit and save valuable time. Information: 8 x 509045P - Bolt differential side4 x BT606101L - UNF fBolt handbrake drum8 x NZ606041L - Fuse Nyloc nut. Fits for: Defender (all models)Discovery 1 (all)Range Rover classic (all)