Defender springs +50 to 70 mm from ENGAGE4X4 with parts certificate

ENGAGE4X4 high performance shock absorbers Step1 for the Land Rover Defender have been developed for the highest loads and extreme requirements. The high performance shock absorbers are designed 80% stronger than conventional monotube or twin-tube shock absorbers. High-performance shock absorbers ENGAGE4X4 Step 1 for all Defender All components are CNC machined from high quality materials. ENGAGE4X4 high performance shock absorbers are fully revisable and can also be tuned to suit different spring rates or various requirements. The rear shocks are equipped with a special bronze dust cap, which makes it impossible for dust and mud to damage the oil seal of the shock absorber. Fields of application Off road, trail, trophy, working, protected vehicles, expeditions, Specifications:Type: monotubePiston: 46 mmPiston rod: 22 mmOil: High performance oil OR-SpecialGAS: Nitrogen 5.0Pressure: Standard 9 BarFillable: min.: 5 - max. 22 Bar depending on settingMaterial:Eye: Fortal 7075Piston: ETG100Piston rod: 20MnCR4 high polishedBody: Precision milled steel tube. Fits:Defender; Discovery 1, Range Rover classic.

Land Rover Defender suspension with TÜV parts certificate If the Defender 90 is raised by longer suspension springs, the front axle shifts to the left, short um -the correct fit of the front axle is no longer guaranteed. This is where the adjustable ENGAGE4X4 Panhard bar (with TÜV parts certificate) comes into play. Further the deflection angles of the front and rear cardan shafts change, so the annoying vibrations in the drivetrain arise, these are installed by the assembly of ENGAGE4X4 pull & push rods (with TÜV parts certificate) to correct the caster front & rear axle. Since this measure is not sufficient for the Land Rover Defender when the chassis is raised, additional reinforced double-jointed cardan shafts are installed to prevent the load on the universal joints and the load on the transfer case. High quality Defender accessories from Germany ENGAGE4X4 complete suspensions are completely TÜV tested and allow a height increase of 30 to 65mm depending on vehicle weight and characteristics. The ENGAGE4X4 "Expedition" suspension kit for the Defender allows a completely legal installation within the range of the STVZO. All with supplied TÜV relevant components are delivered with a TÜV parts certificate. The Expedition complete suspension kit for the Land Rover Defender is available in 3 variants as follows. The Step 1 Kit is supplied with fully demountable and reinforced high performance shock absorbers without balance reservoir. The Step 2 kit is supplied with fully demountable and reinforced high performance shock absorbers with reservoir. The Step 3 kit is supplied with fully demountable and reinforced high-performance shock absorbers with compensation reservoir and 40-fold adjustable compression damping. The different applications of each complete suspension for the Land Rover Defender are explained as follows. Expedition complete suspension Step 1 Occasional trips in Europe to heavy off-road and work use also suitable for higher roof loads. ENGAGE4X4 suspension springs for Defender 90 Progressive suspension springs with coil cut-off on the front axle. Allow so your Defender a 25% articulation of the front axle and thus a better entanglement compared to other chassis. The springs on the front axle ensure perfect suspension tuning. Both front axle springs have been calculated with different wire thicknesses to the respective weight.The rear axle springs are designed to accommodate higher payloads, the slightly progressive articulation of the rear axle springs allow despite everything a much more comfortable ride with your Land Rover. ENGAGE4X4 high performance shock absorbers An ideal suspension setup for an off-road vehicle is "soft-feathered - hard-damped" That's exactly what we've implemented. The ENGAGE4X4 high-performance shock absorbers are based on a monotube damper system and are designed for the highest loads. The high-pressure gas filling acts against premature cavitation (foaming of the shock absorber oil) under high loads. em and are designed for the highest loads. The high-pressure gas filling prevents premature cavitation (foaming of the shock absorber oil) under high loads.