Bolt set Defender chassis

Caster correction front axle for Land Rover Defender. Land Rover Defender axle caster correction kit for the front axle made of high performance polyurethane for vehicles with discreet lift. In case of chassis modifications respectively a slight lifting the axle geometry has to be adjusted as well. If you modify your vehicle, you should do it properly. This heavy-duty correction kit can be used for lift from about 25 to 40 mm. However, we recommend such an adjustment only for vehicles that are not exposed to adverse conditions. Information Bushings tie rods front axle correspond(NTC6781) Bushings mounting tie rods front axle frame side (ANR6971 NRC4514) Material Polyurethane From chassis number LA930456 > until year of manufacture 01.2016

Bearing tie rods for all Land Rover Defender & Discovery 1. Tie rod rubber bearing on frame for all Defender and Discovery 1 models up to chassis number VA130784 in OEM parts quality. Information Up to chassis number: VA130784 Installed quantity/vehicle 4 pieces (quantity to be ordered 1 set = 4 pieces)

To perform a professional suspension upgrade on a Land Rover Defender, you need much more than just springs and shock absorbers. An incorrectly performed suspension modification can lead to the loss of the operating license and even cause damage to your Land Rover Defender. A Defender suspension from ENGAGE4X4 is designed to significantly increase the off-road capability. Caution with incomplete Defender chassis If you lift the Defender with longer suspension springs, the front axle shifts to the left. In short, the correct fit of the front axle is no longer guaranteed. This is where the adjustable ENGAGE4X4 Panhard bar (with TÜV parts certificate) comes into play. Further the deflection angles of the front and rear cardan shafts change. This causes the annoying vibrations in the drivetrain. These are corrected by the installation of ENGAGE4X4 traction & thrust rods (with TÜV parts certificate) to correct the caster front & rear axle. Since this measure is not sufficient for the Land Rover Defender when the chassis is raised, reinforced double-jointed cardan shafts are also installed to prevent the load on the universal joints and the load on the transfer case. Land Rover Defender 90 suspension with TÜV parts certificate The chassis (suspension and shock absorbers) of your Land Rover is the link between the road or off road track and the suspension of your Land Rover Defender. They form the basis safety, ride comfort, as well as durability and extreme loads. Defender suspension high loads ENGAGE4X4 complete suspensions are completely TÜV tested and allow for a height increase of 30 to 65mm, depending on vehicle weight and characteristics. The ENGAGE4X4 "Expedition" suspension kit for the Defender allows a completely legal installation within the range of the STVZO. All safety-relevant suspension components are supplied with a TÜV parts certificate. One chassis for all many applications The ENGAGE4X4 Step 1 complete suspension kit for the Defender 90 is suitable for the following applications. The Step 1 kit is delivered with fully demountable and reinforced high performance shock absorbers with balance reservoir.The different application areas of the individual complete suspension kits for the Land Rover Defender are explained as follows.Expedition Complete Suspension Step 1 For occasional expeditions and trips to remote areas with increased total vehicle weight and higher roof loads such as roof racks or outer cage. The suspension is many times higher loadable than the original Land Rover (Genuine) suspension and comparable suspensions on the market. The shock absorbers can easily cope with long track runs under extreme conditions. The suspension has been successfully tested under extreme conditions on several desert rallies. ENGAGE4X4 suspension springs Land Rover Defender Progressive suspension springs with coil cut-off on the front axle. Allow your Defender so a 25% articulation of the front axle and thus a better entanglement compared to other chassis.For a perfect chassis tuning provide the springs on the front axle. Both front axle springs have been calculated with different wire thicknesses to the respective weight. The rear axle springs are designed for higher payload to be able to absorb, the slightly progressive Auslgegung of the rear axle springs allow despite everything a much higher ride comfort with your Land Rover. Piston dia: 46 mm Piston rod: 22 mmType: Upside Down Damping | High Pressure Dust seal: bronzePressure: 5 to 22 bar (standard 9 bar)

Axle bearing thrust strut rear axle Defender & Discovery 1. OEM suspension bushing for the thrust struts on the rear axle (axle side). Fits all Land Rover Defender, Discovery 1 and Range Rover Classic models. Information Installed quantity/vehicle 2 pieces Parts quality OEM Fits Land Rover 90-130 (all), Defender (all) Discovery 1 and Range Rover Classic.